Closed
Description
Board
ESP32-S3
Device Description
Custom ESP32-S3 keyboard but it should work on any ESP32-S3 devkit with USB connection.
Hardware Configuration
No.
Version
v3.0.4
IDE Name
Arduino IDE
Operating System
macOS 14.6.1
Flash frequency
80MHz
PSRAM enabled
no
Upload speed
921600
Description
I'm currently building a USB keyboard using the ESP32-S3 and when upgrading to the latest Arduino Core, the reporting of LEDs (Caps Lock, Num Lock, etc.) did not happen anymore, even though the typing works. Downgrading to 2.0.13 makes the code work again.
I attached a minimum reproducible example with the expected output when the devkit is connected to a PC.
Sketch
#include <USB.h>
#include <USBCDC.h>
#include <USBHIDKeyboard.h>
USBHIDKeyboard m_keyboard;
USBCDC m_serial;
ESPUSB* m_usb;
static void
usbEventCallback(void* arg,
esp_event_base_t event_base,
int32_t event_id,
void* event_data)
{
if (event_base == ARDUINO_USB_EVENTS) {
arduino_usb_event_data_t* data = (arduino_usb_event_data_t*)event_data;
switch (event_id) {
case ARDUINO_USB_STARTED_EVENT:
m_serial.println("USB PLUGGED");
break;
case ARDUINO_USB_STOPPED_EVENT:
m_serial.println("USB UNPLUGGED");
break;
case ARDUINO_USB_SUSPEND_EVENT:
m_serial.printf("USB SUSPENDED: remote_wakeup_en: %u\n",
data->suspend.remote_wakeup_en);
break;
case ARDUINO_USB_RESUME_EVENT:
m_serial.println("USB RESUMED");
break;
default:
break;
}
} else if (event_base == ARDUINO_USB_HID_EVENTS) {
arduino_usb_hid_event_data_t* data =
(arduino_usb_hid_event_data_t*)event_data;
switch (event_id) {
case ARDUINO_USB_HID_SET_PROTOCOL_EVENT:
m_serial.printf("HID SET PROTOCOL: %s\n",
data->set_protocol.protocol ? "REPORT" : "BOOT");
break;
case ARDUINO_USB_HID_SET_IDLE_EVENT:
m_serial.printf("HID SET IDLE: %u\n", data->set_idle.idle_rate);
break;
default:
break;
}
} else if (event_base == ARDUINO_USB_HID_KEYBOARD_EVENTS) {
arduino_usb_hid_keyboard_event_data_t* data =
(arduino_usb_hid_keyboard_event_data_t*)event_data;
switch (event_id) {
case ARDUINO_USB_HID_KEYBOARD_LED_EVENT:
m_serial.printf(
"HID KEYBOARD LED: NumLock:%u, CapsLock:%u, ScrollLock:%u\n",
data->numlock,
data->capslock,
data->scrolllock);
break;
default:
break;
}
}
}
void
setup()
{
// put your setup code here, to run once:
// m_serial.begin(115200);
USB.onEvent(usbEventCallback);
m_keyboard.onEvent(usbEventCallback);
m_serial.onEvent(usbEventCallback);
m_keyboard.begin();
m_serial.begin(115200);
// m_serial.enableReboot(false);
m_usb = &USB; // get the USB object
m_usb->manufacturerName("TEST MAN");
m_usb->productName("TEST DEV");
m_usb->begin();
}
void
loop()
{
// put your main code here, to run repeatedly:
m_serial.println("Hello World!");
delay(1000);
m_keyboard.press(KEY_CAPS_LOCK);
delay(1000);
m_keyboard.release(KEY_CAPS_LOCK);
delay(1000);
}Debug Message
--- CORRECT OUTPUT WITH ARDUINO ESP32 VER 2.0.13 ---
KEYBOARD LED: NumLock:0, CapsLock:1, ScrollLock:0
Hello World!
HID KEYBOARD LED: NumLock:0, CapsLock:0, ScrollLock:0
Hello World!
HID KEYBOARD LED: NumLock:0, CapsLock:1, ScrollLock:0
Hello World!
etc...
--- OUTPUT WITH ARDUINO ESP32 VER 3.0.0 and 3.0.4 ---
Hello World!
Hello World!
Hello World!
etc...
Other Steps to Reproduce
No response
I have checked existing issues, online documentation and the Troubleshooting Guide
- I confirm I have checked existing issues, online documentation and Troubleshooting guide.